pg电子竞技平台的产品中心 应用方案 技术文摘质量保证产品选型 下载中心业内动态 选型帮助 品牌介绍 产品一览 联系pg电子竞技平台
- fdt压电薄膜传感器中英文产品介绍
- 来源:pg电子游戏官网官方网站-pg电子竞技平台 发表于 2014/7/4
applications: contact microphone, dynamic strain gages, speakers, switches
description: the “f” in fdt series stands for ‘flexible leads’. these are rectangle elements of piezo film with silver ink screen printed electrodes. rather than making the lead attachment near the sensor, the piezo polymer tail extends from the active sensor area as flex circuit material with offset traces. this gives a very flat, flexible lead, with a connector at the end. the fdt elements are available in a variety of different sizes and thicknesses. they are available without a laminate (fdt), with a laminated (0.005” mylar) on one side (fldt) or with tape release layer adhesive (fdt with adh) in the sensor area. the connector pins on the fdt sensors can be directly soldered to a pcb with a reasonable level of care. this component cannot withstand high temperatures (> 80°c), and therefore coldering of the pins to a pcb must be done quickly. a heatsink clamped to the interface area between the film and the crimps will take the heat away from the film. pre-tin the pins and then quickly solder them to the board. do not allow the soldering iron to touch the film, and do not use a dwell time of over 5 seconds on the pins. low temperature solder can also be used.
features:
very flat, flexible lead
available in a variety of different sizes and thicknesses
available without a laminate (fdt)
available with a laminated (0.005” mylar) on one side (fldt)
available with tape release layer adhesive (fdt with adh) in the sensor area
connector pins on the fdt sensors can be directly soldered to a pcb with a reasonable level of care
典型应用: 接触式麦克风,动态应变计,扬声器,开关
产品描述:
"f"在fdt系列里代表“柔性引线”。fdt系列是带银墨丝印电极的矩形压电薄膜元件。与其他接出引线的压电薄膜元件不同,带电极的压电薄膜从动态传感区域延伸出来作为柔性电路板,末端带有连接头,从而使得pg电子游戏官网官方网站-pg电子竞技平台的引出非常扁平,而且柔软。fdt系列有许多不同的尺寸和厚度可供选择。客户可以选择没有聚酯基片的fdt,一面有聚酯基片(0.005”)的fldt,或传感区域附有双面胶的fdt。fdtpg电子游戏官网官方网站-pg电子竞技平台末端的插针可直接焊接到pcb。元件不能承受高温(> 80°c),因此焊接需要迅速完成。夹在压电薄膜和连接头连接处的散热器能迅速把热量带走。提前给插针上锡,然后迅速焊接到电路板上。不要用烙铁接触压电薄膜,焊接时间也不能超过5秒钟。可用低温焊接。
特点:
引线扁平,柔软
多种尺寸和厚度可选
可选无聚酯基片fdt
可选一面带有聚酯基片(0.005“)fldt
可选传感区域带有双面胶的fdt
fdt末端插针可直接焊接到pcb
fdt系列传感器更多技术参数及规格书下载请浏览:http://www.sensorway.cn/sensors/119.html
北京赛斯维测控技术有限公司产品咨询热线:010-84775646,84775648。
- 如果本文收录的图片文字侵犯了您的权益,请及时与我们联系,我们将在24内核实删除,谢谢!